Accessories TERME'KS BR-01T, THERMOTEST-100-P, etc.

Accessories for viscosity determination equipment.

• Illumination lamps: VIS-T-01-L, VIS-T-08L, VIS-T-11-L.
• Stand for cryostats of the CRYO-VIS-T-05 model range.
• Vertical indicator for VIS-T-I viscometers.
• Tripods for viscometers VIS-T-Sh4, VIS-T-Sh6.
• Set of devices VIS-T-11-K

---

Accessories for density determination equipment.

• Glass cylinder for hydrometers.
• Metal cylinder for hydrometers.
• Stand VT-ro-P for thermostats VT‑ro‑01, VT‑ro‑02 and VT‑ro‑03. Provides convenience in measurements, allowing you to install cylinders for hydrometers at eye level.
• State standard samples for calibration and verification of density measuring instruments: RAP-1, RAP-2, RAP-3, RAP-4, RAP-5, RAP-7, RAP-8.

---

Accessories for oil and petroleum products analysis equipment.

• Raid Bomb BR-01T, BR-02T.
• Rubber sealing ring for the liquid chamber of the Raid bomb.
• Pressure gauges.
• O-ring for pressure gauge.
• Stand for pressure gauges MTIf-P.
• The standard of corrosion.
• The ExT-01/2-K-Z transport console with grounding is designed to carry the ExT‑01/2 thermometer between measurement locations. Allows you to place the measuring unit, conveniently lay the cable, fix it with a spring clip and place the sensor in the transport pocket. Equipped with a shoulder strap and a quick-release grounding cable.
• The TMP-D holder is designed for simultaneous polishing of four copper plates used in determining the corrosion effect in accordance with GOST ISO 2160, GOST 32329, GOST 6321 and GOST 2917.
• The CRYON-1-TP sliding cabinet is designed for convenient placement of an installation for cryoscopic determination of the molecular weight of CRYON‑1.

---

Accessories for metrological equipment.

• Holders for thermometers with diameters from 3 to 9 mm and from 16 to 20 mm..
• Stand for cryostat THERMOTEST-100, THERMOTEST-300.
• Baskets for thermostats
• Fume hood for thermostat THERMOTEST-300 and cryostat THERMOTEST-100.
• Reference resistance thermometers.
• USB-COM adapter for LT-300.
• Terminal block for thermostats TERMOTEST-05-02, TERMOTEST-100 and TERMOTEST-300.

---

Accessories for laboratory tables.

• Add-ons for laboratory tables, washing tables.
• Hanging and sliding cabinets for laboratory tables.

---

Heat carriers:
PMS-10 is a polymethylsiloxane liquid for the operating temperature range of -30...+100 °C. It is supplied in aluminum cans with a volume of 10 liters. The density is 0.935 g/cm3.
PMS-20 is a polymethylsiloxane liquid for the operating temperature range -30...+100 °C. It is supplied in aluminum cans with a volume of 10 liters. The density is 0.950 g/cm3.
PMS-100 is a polymethylsiloxane liquid for the operating temperature range +90...+300 °C. It is supplied in aluminum cans with a volume of 10 liters. The density is 0.966 g/cm3.

---

The USB-RS485 adapter is used to connect TDS thermometers and MASTER thermostats equipped with an RS‑485 interface to a personal computer via a USB interface.
The use of this adapter does not require the installation of additional drivers because it uses the HID driver built into the operating system to exchange data.

---

The temperature equalization unit TERMOTEST-B1 is designed to improve short‑term temperature stability during verification and calibration of electronic thermometers LT‑300 and LTI in calibration thermostats TERMOTEST‑100, TERMOTEST‑300, TERMOTEST-05 and TERMOTEST-05-1.

---

The THERMOTEST-D1, THERMOTEST-D2 holder with flat steel springs allows you to install and securely fix up to 6 verifiable thermometers with a diameter of the submerged part from 3 to 9 mm.

---

The MAU-1 analog control module is designed for remote control of MASTER series thermostats via the 4-20 mA current loop analog interface. The module performs mutual data conversion of a digital bidirectional RS-485 channel and two 4-20 mA analog channels (input and output).

---

Weighting rings K-050, K-070 are designed to prevent the flask from surfacing when it is thermostated in a laboratory bath or a liquid thermostat.

---